![uses for hp mediasmart server ex470 in 2015 uses for hp mediasmart server ex470 in 2015](https://i.ytimg.com/vi/K3E7KBM9HNk/maxresdefault.jpg)
- USES FOR HP MEDIASMART SERVER EX470 IN 2015 HOW TO
- USES FOR HP MEDIASMART SERVER EX470 IN 2015 INSTALL
- USES FOR HP MEDIASMART SERVER EX470 IN 2015 DRIVERS
- USES FOR HP MEDIASMART SERVER EX470 IN 2015 SOFTWARE
- USES FOR HP MEDIASMART SERVER EX470 IN 2015 PC
A boost in storage elements from Seagate 7200.11 500GB drives (one for EX470, two for EX475) to 750 GB drives in the same series (one for EX485, two for EX487).A bump from 512 MB of PC2-5300 RAM to 2.0 GB of PC2-6400 RAM (Alex Kuretz at indicates the BIOS on the 48* models can handle speeds up to 1,066 MHz).A shift from a 90 nm 1.8 GHz Sempron 3400+ to a 65 nm 2.0 GHz Celeron 440 processor.Or pull all your drives out and try it on a spare system drive. Just so you don’t mess things up, I recommend that you have your server shares backed up. Server Recoveries will be a lot easier now. Now go ahead and Restore your EX490 while it’s still connected to the network. Run the newly created Server Recovery DVD. Wait 5 seconds then push the system drive back in. ( this is so you don’t have to fiddle with the reset pin).
![uses for hp mediasmart server ex470 in 2015 uses for hp mediasmart server ex470 in 2015](https://m.media-amazon.com/images/I/41adRiCYKdL._AC_SX450_.jpg)
Pull the system drive out 1 inch so that it does not make contact with the rear back plate.
USES FOR HP MEDIASMART SERVER EX470 IN 2015 INSTALL
Install the bootable USB key into the bottom rear USB port. Copy this disk to your desktop, then replace the Recovery Image folder with the same folder from the EX490/5 Disk.
![uses for hp mediasmart server ex470 in 2015 uses for hp mediasmart server ex470 in 2015](http://www.mediasmartserver.net/blog/wp-content/uploads/2010/05/PowerSupplySideBySide.png)
This is the EX470/5 Server Recovery Disk.
USES FOR HP MEDIASMART SERVER EX470 IN 2015 SOFTWARE
You can also replace the Home Server Connector Software with the one from the EX490/5 Software Installation Disk. What you need to do is create a DVD using the EX470/5 DVD boot stuff but replace the server image in “\Recovery Image\volume.image” with the server image from the EX490/5 DVD. If you use the EX490/5 Server Recovery DVD as is, it will try and run the PXE boot stuff.
USES FOR HP MEDIASMART SERVER EX470 IN 2015 PC
Test it on your PC and boot from it to see if the Server recovery software starts, if it does, shut down your PC and remove it. Now your external USB Bootable Server Recovery Thumb Drive is ready. Next, open up the SOURCES folder and replace the boot.wim file with the boot.wim file from your EX490/5 Server Restore DVD.
USES FOR HP MEDIASMART SERVER EX470 IN 2015 DRIVERS
5.742 Replace the drivers in the \drivers folder with the new ones. Next, since the EX490/5 has a different NIC card, you need the drivers from Realtek. Now go back and enable that MediaSmart Server device. Now open My Computer you should see the hidden partition and copy those file to your PC where you will work with them. RDC into your EX470, right click My Computer, properties, hardware, device manager, open up System devices, disable the MediaSmart Server device, reboot. Since it’s a hidden partition you need to unhide it. Next, you need the boot software from the hidden partition on the EX470/5. For simplicity, follow this link to format the thumb drive. 2 GB stick, but you can start with a 256MB stick, use whatever costs less. So you will have to test the thumb drive, more on this later. This is important to know because you might have done everything right and it still doesn’t work. The software you will need can be found on the EX470 hidden flash, the EX470/5 Server Recovery Disk, the EX490/5 Server Recovery Disk and the EX490/5 network drivers from Realtek’s website.įirst off, not all USB thumb drives are equal.
USES FOR HP MEDIASMART SERVER EX470 IN 2015 HOW TO
So I’ll show how to create a bootable USB thumb drive to use on your EX490/5 so that you can restore your server pretty much just like it’s done on the EX470/5. If you have a EX470/5 and a EX490/5 then you already have most of what you need. I’m not happy about that because it was easier on the EX470/5 and I was spoiled. All this without a VGA connection on your server. Then you must have the correct timing to press the reset pin. You also have to turn off your firewall and anti-virus software. Now you must have a direct connection between your server and the PC that will run the Server Recovery DVD. However I find that removing the internal 256 MB flash is a mistake. The HP EX490/5 so far has been HP’s best home servers yet. Everything has been improved, right, WRONG. Ok, so you love your EX470/5 but you want to move on to the new EX490/5, it’s time.